2014-2018 Chevrolet Equinox Auto Start Stop Eliminator
Description
Keep ordinary traffic pauses from becoming engine-off events
If you prefer your equipped Equinox to remain running at normal standstills, our hood-switch eliminator addresses that automatic stopping routine without adding a visible cabin control. It uses an inline connection under the hood, so there is no device to leave hanging from the diagnostic port.
Check the Equinox generation as well as the year
The 2014–2018 application crosses the Equinox's 2018 redesign. Stop/Start equipment on the newer generation should not be projected onto an earlier vehicle merely because both are called Equinox. Confirm that the vehicle actually performs the factory automatic engine-stop function you want to change.
Then compare the hood-switch plug itself. Match the keyed housing, terminal face and latch to the larger connector pictured. Nearby engine-bay connectors can look similar; identify the hood-latch switch connection rather than choosing a plug by its color or proximity to the radiator.
A short connection without cabin disassembly
The approximately 5.71-inch harness has black corrugated protection and two mating ends. It sits between the original vehicle loom and the hood switch. There is no need to remove the radio, console or steering-column trim for this connection, and the original wires do not need cutting or splicing.
Because it uses the hood-switch interface, this is a different approach from a device that repeats a dashboard button press. Select the actual connector version rather than assuming every start-stop eliminator uses the same installation point.
Connect at the hood switch, not a cabin button
Park securely, switch the ignition off and keep the key away from the work area. Open and safely support the hood. Locate the electrical connection at the hood-latch switch and compare its keyed face, terminals and locking arrangement with the harness. Stay clear of hot parts, belts and cooling fans.
Release the connector's secondary lock where fitted, press its latch and separate the housings without pulling the wires. Insert the added harness between the original loom and switch, then check that both ends seat and lock. Route the lead away from the latch movement, hood-closing path and sharp or hot surfaces. A connector that resists seating needs rechecking, not trimming or force.
Choose the behavior change, not a performance claim
The intended change concerns the engine stopping while the Equinox is stationary under qualifying conditions. It is separate from cylinder deactivation, and it does not retune the engine or transmission. Continuing to run at a stop also means foregoing the engine-off portion of normal stop/start operation at that moment; a fuel-economy gain is not the reason to choose it.
Finish with a physical and functional check
Remove tools from the engine bay and make sure the hood closes and latches securely. An electrical signal never replaces the physical latch. Check the instrument display for new messages and check hood-dependent functions before driving, including remote-start operation if the vehicle has it. Hood-switch signals also serve other vehicle functions, so check actual operation rather than assuming those functions are unchanged.
Factory stop/start also depends on operating conditions. Observe behavior on a normal drive rather than treating one stop with the engine running as a complete check. If a warning appears or a function changes unexpectedly, switch off and inspect the installation; restore the original connection if necessary.
Removal and useful vehicle information
With the ignition off, unplug the added harness and reconnect the factory loom directly to the hood switch. Confirm the hood latches and the related functions operate afterward. For selection help, provide RC-ASSE-02-02, the Equinox model year and engine, plus clear photographs of the actual connector face and lock. An existing hood-ajar message or start-stop fault needs diagnosis separately.
Vehicle Fitment
Additional Information
| Brand | Recontrol-X |
Reviews
FAQ
Is this an Equinox dashboard-button module?
No. RC-ASSE-02-02 connects inline at the electrical hood-latch switch under the hood.
Does a 2014–2018 year entry prove the same factory system?
No. The range crosses the all-new 2018 Equinox. Confirm the actual Stop/Start equipment and the hood-switch connector on the vehicle.
Do I need to remove the radio or console?
The connection is under the hood. Cabin trim removal is not the installation route for this harness.
What connector details should I compare?
Compare the larger plug keyed profile, terminal face and locking arrangement. The illustrated harness is approximately 5.71 inches long.
Will this repair a hood-ajar warning?
No. A warning caused by the latch, sensor or original wiring needs diagnosis. Check physical hood closure and any new message after fitting.
How is it removed?
Switch off, unplug both added connections and reconnect the original vehicle loom directly to the hood switch. Check related functions after restoration.