2015-2020 Ford F-150 Auto Start Stop Eliminator – OBD-II Plug-In Module
Description
Skip the dashboard work. Keep automatic engine stops off.
If you prefer your F-150 to stay running at traffic lights and in slow queues, turning Auto Start-Stop off should not become another task at the beginning of every trip. Our RC-ASSE-10-01 controls that automatic-stop function through the truck’s diagnostic connection while the module remains plugged in.
The practical advantage is the installation: reach the OBD-II socket beneath the driver-side dashboard and connect the compact device directly. You do not need to remove the center dash trim, reach behind the hazard-switch assembly or choose a harness by which side of the screen the Start-Stop button sits.
Is the OBD version the right choice for your truck?
- Application: 2015–2020 Ford F-150 equipped with factory Auto Start-Stop.
- Connection: the original OBD-II diagnostic socket under the driver-side dashboard, above the brake-pedal area.
- Best reason to choose it: you want a direct-access installation without dismantling the switch panel.
- The trade-off: it occupies the diagnostic socket while in use, so another device cannot plug directly into that same socket at the same time.
Check the actual factory equipment, not just the model year. An F-150 without Auto Start-Stop has no automatic-stop function for this module to disable. The plug-in OBD device shown in the main product and dimension photos is the format described here; an inline cable connects differently and is not the installation route for this module.
A small module still needs the right clearance
The housing measures approximately 1.89 × 0.95 × 0.83 inches as shown in the dimension image. Check the installed position at the socket, rather than judging clearance from the housing size alone. The connector and the angle of the vehicle’s port affect how the device sits under the dash.
The brake pedal must move through its full travel without touching the module, and your footwear must not catch it when entering, driving or getting out. A secure direct connection keeps the device at the socket instead of leaving a cable or loose component in the footwell.
Install directly at the diagnostic port
- Park safely. Apply the parking brake, select Park and switch the ignition fully off before fitting the accessory.
- Find the OBD-II socket. Look under the driver-side dash above the brake-pedal area, using the installation photo to identify the diagnostic connector—not the Auto Start-Stop switch.
- Inspect and align. Check that the socket is undamaged and unobstructed. Match the module’s keyed connector to the socket and insert it straight until securely seated. Do not force a misaligned plug.
- Check the footwell. Make sure the installed module is clear of pedal movement and the driver’s feet. Do this before driving, not after noticing contact on the road.
- Check operation. Start the truck, review the Auto Start-Stop status using the unit’s directions, then switch off and restart to check the result across an ignition cycle.
No dash disassembly, drilling, cutting or splicing is involved in this direct-port installation. Keep the module connected during use; this is not a flash-and-unplug programmer.
What to expect after installation
The intended change is straightforward: the engine keeps running instead of performing a normal Auto Start-Stop shutdown at a stop. The module is for that driving preference, not extra horsepower or a change to the transmission’s shift behavior.
Judge the result by the system status and repeat startup behavior, not by one traffic light. A factory-equipped F-150 may already keep its engine running because it is warming up, the battery needs charging or the cabin needs heating or cooling. Those conditions can make an engine-on observation look like a successful disable even without a module.
If automatic stops continue, switch off and check that the correct device is fully seated in the original port. If there is a warning, a starting problem or another abnormal response, remove the module with the ignition off and have the cause checked. Send us the model year, the exact message and a photo of the installed device for focused assistance.
Service visits, removal and everyday port access
When a technician needs the diagnostic socket, switch the truck off and unplug the module before the scan tool is connected. The same applies to an inspection device or another accessory that requires the port. A splitter is not a substitute for verified compatibility between devices.
Removing our module frees the socket and removes its automatic-stop control. Reconnect it securely after service if you want to use it again, then recheck clearance and startup behavior. Keep the removed unit out of the footwell and tell the technician what was connected if a fault is being investigated.
Keeping the engine running can increase fuel use during time that Auto Start-Stop would otherwise save idling fuel. Choose this accessory for the engine-on routine you prefer, not a promised MPG gain, battery repair or longer starter life. Our Auto Start-Stop guide explains the factory function and the different connection styles.
Vehicle Fitment
Additional Information
| Brand | Recontrol-X |
Reviews
FAQ
Does installation require removing the F-150 dash or Start-Stop switch?
No. RC-ASSE-10-01 plugs directly into the OBD-II diagnostic socket under the driver-side dashboard, above the brake-pedal area. It is not the behind-switch inline-harness version.
Do I leave the module plugged in after installation?
Yes. Leave it connected for its automatic-stop disable function. It is not a one-time programmer. With the ignition off, unplug it when you want to remove the accessory or need the diagnostic socket.
Will it fit every 2015–2020 F-150 just because the year matches?
The truck must have factory Auto Start-Stop, and the original diagnostic port must be available. Check the module’s installed position and full pedal clearance. A truck without Auto Start-Stop has nothing for this module to disable.
Can I use an OBD scanner, tracker or other dongle at the same time?
The module occupies the original socket and has no pass-through port. Switch off and remove it before connecting diagnostic equipment. Do not assume an OBD splitter makes simultaneous devices compatible.
How much space does it need around the brake pedal?
The pictured housing is approximately 1.89 × 0.95 × 0.83 inches. Check the complete installed position, including the connector, and keep it clear of the brake pedal’s full travel and the driver’s footwear.
My engine stays on at some stops already. How should I check the module?
Check the Auto Start-Stop status and repeat the check after switching off and restarting. Factory battery, warm-up and climate conditions can keep the engine running even when Auto Start-Stop is enabled. If a warning or starting concern appears, switch off, remove the module and investigate it separately.