2018-2024 Audi SQ5 Auto Start Stop Eliminator | Plug & Play
Description
2018-2024 Audi SQ5 Auto Start Stop Eliminator
The Audi Start/Stop system can shut the engine off automatically during eligible stops and restart it when the vehicle needs to move again. Audi documentation for this platform explains that the Start/Stop system is automatically activated when the ignition is switched on. For drivers who consistently choose the off setting, that means the A/OFF button can become a repeated step after starting the vehicle.
Automatic Start/Stop-Off Preference for 2018-2024 Audi SQ5
The Recontrol-X Auto Start Stop Eliminator is designed for the 2018-2024 Audi SQ5 vehicles identified in the supplied fitment sheet. After installation, the module automatically places the factory Start/Stop function in the off state after startup, handling the preference without requiring the same manual button press at the beginning of each drive.
The product is a convenience module only. It does not tune the engine, change transmission behavior, increase performance, or repair a Start/Stop system that already has a fault.
Inline Hardware Instead of a Software-Coding Change
The supplied installation guide shows the eliminator connecting at the original A/OFF switch. Two panel-release tools are inserted into the lower access slots of the center control panel, the button panel is pulled forward, and the factory A/OFF connector is unplugged. The Recontrol-X harness is then placed between the button and the original vehicle cable.
The complete module is shown at approximately 5.70 inches long. Once both connectors are fully seated, the harness can be routed behind the panel so the installation remains concealed when the original trim is put back in place.
No Cutting, Splicing, or OBD Coding in the Supplied Steps
The provided procedure does not show any need to cut factory wires, splice conductors, drill the dashboard, flash the ECU, or connect an OBD-II coding tool. The module instead uses the existing Start/Stop switch circuit and matching plug-in connectors.
During installation, make sure the connector locks click into position. Keep the short harness away from panel edges or mounting points that could pinch the cable during reassembly.
Factory Button Control Is Preserved
The goal is to automate the preferred default, not delete the factory interface. If you decide you want Start/Stop active during a specific drive, the original A/OFF button remains available to change the setting. SQ5 owner discussions concerning this same product family likewise describe the factory button continuing to work after installation.
Easy to Return to the Original Wiring Arrangement
The connector-based layout also makes the product reversible. If the module is no longer wanted, disconnect it and reconnect the original factory A/OFF plug directly to the button. Because the supplied method does not require cutting the vehicle harness, there is no need to repair a spliced wire simply to remove the accessory.
Model-Year Fitment Must Be Verified
The supplied fitment data lists 2018, 2019, 2020, 2021, 2022, 2023 and 2024 Audi SQ5. No separate trim or engine combinations are provided. Confirm that your vehicle has the matching factory A/OFF button and compare the connector and control-panel configuration with the product images before ordering. Do not extend this listing to other Audi models or additional model years simply because a similar button is present.
What to Check Before Checkout
Match the SQ5 A/OFF switch and connector to the supplied photos before purchase. If your control panel or plug differs, verify compatibility first. Existing Start/Stop fault messages should be diagnosed as faults; this product is intended to manage the normal Start/Stop preference, not repair a malfunction.
For the correct SQ5 application, the important advantages are practical and specific: automatic Start/Stop-off preference after startup, retained factory-button control, compact hidden installation, no software-coding step in the supplied procedure, and reversible factory-style connectors.
Vehicle Fitment
Additional Information
| Brand | Recontrol-X |
Reviews
S&Q
Does this fit my 2018-2024 Audi SQ5?
The supplied fitment lists 2018 through 2024 Audi SQ5. Because trim and engine coverage are not separately specified, compare your A/OFF control and connector with the product images before ordering.
Does the module permanently delete the Start/Stop system?
No. It automatically places Start/Stop in the off state after startup, but the factory system and original A/OFF control remain available when you want to change the setting.
Do I have to cut or splice any factory wires?
No cutting or splicing appears in the supplied installation procedure. The module plugs inline between the original A/OFF button and factory vehicle connector.
Is OBD coding or ECU programming required?
The supplied installation uses the factory button connector and does not show an OBD-II coding, VCDS/OBDeleven, or ECU-flashing step.
What if my SQ5 already has a Start/Stop warning?
An existing warning or malfunction should be diagnosed separately. This product is intended to manage the normal Start/Stop preference and should not be treated as a repair for an electrical or Start/Stop system fault.